|
Contact AMS Customer Service for Special Pricing on Larger Quantities.
|
 |
|
|
|
|
|
|
AMS Pneumatic Press
The AMS #AP-2 Press enables quick installation of self-fastening hardware onto backing boards and wood frames. Its work surface is made of a 12” x 18” (30cm x 46cm) steel plate that is 1/4” thick; a measuring tape is attached to the right and left edges. The press includes safety features of (1) a clear acrylic front guard, and (2) twin recessed buttons that activate mechanism only when simultaneously pushed by both hands of operator. A 2” (5.1cm) stroke is preset and needs no depth adjustment. Use magnetic die heads listed below.
The AMS #AP-2 Press runs via compressor at a recommended air pressure of 10-100 PSI (2.7 - 6.8 BAR) with a maximum force of 3610 LBS (1640 kgs) - 0.36 CFM. An adjustable pressure regulator and gauge are shipped with press, however a compressor is a separate purchase. Press dimensions are 19.5” x 18” x 17” (50cm x 45cm x 43cm); weight is 93 LBS (36.6 kgs). |
 |
| |
|
|
AMS Pneumatic Press |
AP-2 |
$ 1995.00 |
|
| |
|
|
|
Steel Guide for Air Press: This 42” (1.07M) long work surface fence is used as an easily adjusted depth stop in conjunction with the ruler tapes supplied with the table. It is also used as a lateral parts positioner when working with the stops included. |
SG-1 |
$ 230.00 |
|
| |
|
|
|
Pivoting Flip Stop: Used with the steel guide to allow additional positions for part installation. |
PVS-1 |
$ 85.00 |
|
| |
 |
|
Steel Block for Installation of Kwik Hangers
Magnetized hand-held steel block used to hold AMS #KH-2B Kwik Hangers in place while hammering into backing board. For large jobs, consider AMS Presses #AP-2 and #HP-2C equipped with AMS #MPH-03 die head.
KH-BLOCK $ 95.00 |
| |
AMS Hand-Operated Toggle Press
The AMS #HP-2C Hand-Operated Toggle Press enables quick installation of self-fastening hardware. It is user friendly, light weight and can be shipped via UPS. Hardware is affixed to backing boards with the help of left and right centering guides. Use magnetic die heads listed below. |
 |
| |
|
|
AMS Hand-Operated Toggle Press |
HP-2C |
$ 350.00 |
|
| |
|
|
|
Guide for hand press. |
HP-2C1 |
$ 174.50 |
|
| |
|
|
|
Center disc required to install hangers. |
HP-2C2 |
$ 73.50 |
|
| |
|
|
|
Adaptor to fit magnetic head to press
. |
PMP-303 |
$ 28.00 |
|
| |
|
|
|
Center disc required to install easel hinges. |
HP-3C1 |
$ 78.00 |
|
| |
 |
|
Magnetic Die Heads
These Magnetic Die Heads are used on the presses detailed above for the installation of AMS “starburst” or “press-in” hardware. Hardware is held in place magnetically with two spring-loaded alignment pins that retract back into the die as part is inserted. Other die heads are available upon request. |
| |
|
|
Small Nailess Sawtooth Hangers - SW1/HW1 |
MPH-01 |
$ 100.00 |
|
| |
|
|
|
Large Nailess Sawtooth Hangers - MICA2/HDWD2 |
MPH-02 |
$ 100.00 |
|
| |
|
|
|
Kwik Hangers - KH-2B and KH-3 |
MPH-03 |
$ 100.00 |
|
| |
|
|
|
V-Clip Staples - 523-3A & 523-3B |
MPH-04 |
$ 100.00 |
|
| |
|
|
|
Easel Hinges - K18 - Use with HP-3C1. |
HP-3C31 |
$ 78.00 |
|
| |
|
|
|
Easel Hinges - K17 - Use with HP-3C1. |
HP-3C32 |
$ 78.00 |
|
| |
 |
